2017年4月9日星期日

Fatigue Performance Analysis of Automobile Engine Crankshaft




Crankshaft is an important part of the car engine, both in the car crankshaft R & D or actual production stage, need to test the fatigue performance of the car crankshaft. In the actual operation of the car engine, the crankshaft to bear the form of the load for the bending and torsional load, so the actual case shows that the main form of failure of the car crankshaft fatigue damage. In addition, if the engine crankshaft output power is large, the greater the torque generated, will produce a certain degree of torsional fatigue damage. Early automotive engine crankshaft used by the material for the 40Cr and 42CrMo and other carbon quenched and tempered steel. However, since the late 1990s, a large number of automotive crankshaft began to widely use non-quenched and tempered steel, especially for heavy-duty engine crankshaft production, the materials used mainly include 48MnV and C38N2, these two materials and medium carbon Compared with the quenched and tempered steel, in the case of ensuring the same strength, a lot of conditioning process is omitted. In recent years, the use of ductile iron production of engine crankshaft has better mechanical processing performance and bending fatigue strength, especially in the use of heavy-duty engine to show a good application prospects.

Automotive crankshaft in the design, the choice of raw materials, forging, machining and heat treatment and surface strengthening of all aspects, if any one part of the mistakes will cause the engine crankshaft failure. A company combined with the actual bearing production case, introduced and analyzed the car engine crankshaft common failure form and internal reasons.

The factors that affect the fatigue strength of the crankshaft of the vehicle mainly include the stress concentration, the size, the surface condition and the environment medium at the journal. In these factors, stress concentration and size and surface state are most important. The factors that affect the stress distribution of the crankshaft mainly include the design shape of the crankshaft and the basic properties of the material. The bending fatigue strength of the crankshaft can be improved by changing the kind and size of the material, but this will greatly increase the manufacturing cost of the material. In the actual application process, the surface strengthening process is usually used to improve the fatigue strength of engine crankshaft. Under the effect of variable load, the maximum stress should appear in a range near the rounded corners of the crankshaft due to the abrupt change in the shape of the crankshaft journal Inside. Research indicates:

(1) Fatigue test of automobile crankshaft The fatigue limit of crank moment is 96.7MPa, the crankshaft stress concentration coefficient is 6.72, and the fatigue test process is in the middle of crankshaft journal. The safety factor at 99% was 1.31.
(2) SEM microstructure analysis of the microstructure and crack fracture of the 40Cr crankshaft journal shows that the microstructure after 40Cr quenching and tempering is tempered sorbite + ferrite + few bainite, conforms to the relevant standard The Fracture analysis shows that the 40Cr crankshaft fracture is a typical dimple and step mixed fracture, and no obvious inclusions.
(3) From the chemical composition and tensile properties of the material and the hardened layer of the journal surface, it can be seen that the reason of the fatigue failure of the crankshaft can exclude the influence of the above factors.
(4) crankshaft drilling hole in the journal internal wall caused by stress concentration, more prone to defects; crankshaft journal under the action of alternating stress is prone to fatigue cracks and expansion, resulting in early fracture of the crankshaft.

2017年4月6日星期四

What is the maintenance of the car ignition system?



Ignition coil if the use of improper use, will cause damage to the ignition coil, it should be noted that the following: to prevent the ignition coil heat or moisture; do not run the engine when the ignition switch; often check, clean, tighten the circuit connector, to avoid short circuit or china ignition system on the water can only be wiped with a cloth, must not use the fire baking, otherwise it will damage the ignition coil.

Spark plug maintenance:

Spark plug function and characteristics: the role of the spark plug is the ignition coil generated by the pulse of high voltage into the combustion chamber, the use of electrodes generated by the spark ignition mixture to complete the combustion.

The domestic spark plug model consists of three parts or letters. The preceding number indicates the diameter of the thread, such as the number 1, that the thread diameter is 10mm, the middle of the letter that the spark plug into the cylinder part of the length; the last digit that spark plug heat type: 1-3 for the heat type, 5,6 for Medium, more than 7 for the cold type china ignition system.

Spark plug "gap" is its main technical indicators, the gap is too large, the ignition coil and the distributor of high voltage is difficult to skip, resulting in the engine starting difficult; such as the gap is too small, will lead to weak spark, and prone to leakage.

Check the spark plug:

1, the demolition: the spark plug on the high-pressure sub-line in turn removed, and in the original position to mark, so as not to install dislocation. Remove the dust and debris from the spark plug hole in advance to prevent the debris from falling into the cylinder. Disassemble the spark plug sleeve with a spark plug, remove the sleeve and remove it in turn.

2, check: spark plug electrode normal color is gray, such as the electrode burned with carbon deposition, then there is a fault. Check the spark plug and the cylinder conduction, with the central high-voltage line to contact the spark plug terminal, and then open the ignition switch to observe the high voltage electric jump position. Such as the jump position in the spark plug gap, then the role of spark plugs good, otherwise, that is necessary to change china ignition system.

Spark plug electrode gap adjustment: a variety of models of spark plug clearance are different, generally should be between 0.7-0.9, check the gap size, available spark plug gauge or thin metal sheet. If the gap is too large, you can use the screwdriver gently tapping the external electrode, so that the gap is normal; gap is too small, you can use the screwdriver or metal sheet inserted into the electrode outside the pull.

Spark plug replacement: spark plug is easy to consume parts, the general driving 20000-30000 km that should be replaced. The spark plug is replaced by a sign that is not flashing, or the electrode discharge part is rounded by ablation. In addition, if found in the use of spark plugs often coke, off the fire, usually because the spark plug too cold, need to use hot spark plug; if hot ignition or the impact of the cylinder sound, you need to use cold spark plug.

Spark plug clean: spark plugs have oil or coke should be promptly cleaned, but do not use the flame barbecue. If the ceramic core is damaged and broken, it should be replaced.

The maintenance of the distributor:

Cleaning: usually use a rag to wipe the distributor cover and sub-fire head, and check for damage or crack. If the center electrode of the carbon rod or spring damage or failure, should replace the distributor cover.

Contact grinding: the contacts of the distributor after a period of use, the surface will appear uneven, so that the impact of ignition timing, or bad spark, or cause the engine idle instability, acceleration is not good, or even unable to start When the sandpaper used to polish, until the removal of the signs on the ablation.

Contact clearance adjustment: use the starting handle to turn the engine crankshaft, and then release the fixing screw, the appropriate thickness of the thick sheet (0.35 ~ 0.45mm) inserted in the contact, with a screwdriver to adjust the screw, The resistance is appropriate, and then tighten the screws and check again.

Working Principle and Introduction of Electric Fuel Pump for Automobile Engine



Fuel pump assembly The role of the fuel pump is stored in the fuel tank fuel to the fuel injector fuel pipeline. Early engine fuel systems in the fuel pump mostly mechanical, and now electric fuel pump has been replaced china delivery valve. In addition, some of the original installed in the fuel tank outside the electric fuel pump, taking into account the heat, noise and air resistance and other issues, are also built into the fuel tank.

Fuel pump assembly

The purpose of the fuel pump is to store the fuel stored in the fuel tank china delivery valve to the fuel line of the injector. Early engine fuel systems in the fuel pump mostly mechanical, and now electric fuel pump has been replaced. In addition, some of the original installed in the fuel tank outside the electric fuel pump, taking into account the heat, noise and air resistance and other issues, are also built into the fuel tank. The fuel pump is installed in the tank and is combined with the fuel oil meter measuring device as a whole.

Fuel pump on the fuel gauge paddle metering part

The working principle of the electric fuel pump is the same as that of the electric water pump, and the corresponding oil pump device is driven by the motor, so as to continuously feed the fuel oil to the fuel system. To know that the fuel system must maintain a certain pressure, the only way to ensure that the fuel injection device fuel spray better, more easy to burn. But when the engine is turned off, the fuel system pressure will be lost, once there is no residual pressure, at high temperatures in the pipeline is easy to produce air resistance. So that when the engine restarts, because the fuel system into the air, it is difficult to ensure adequate fuel, the engine will be difficult to start. For this purpose, a check valve is provided in the fuel pump. So that when the fuel pump stops running, the check valve is closed to maintain the residual pressure in the fuel line to facilitate the restart of the engine. In addition, I do not know if you have noticed, when your vehicle after a long time parked, if the car is relatively quiet, when you open the ignition switch in no hurry to start the engine, you will hear the rear of the vehicle came "buzzing" sound. This is not a malfunction, but in order to ensure that the fuel system has enough pressure to start the engine, let the electric fuel pump run in advance 2-3 seconds to build oil. In order to prevent the electric fuel pump out of the port side of the pressure is too high, but also designed a safety valve, so that once the fuel pump fuel pressure is too high, china delivery valve will open, so that the pressure of high fuel back to the fuel tank.

Fuel pump and engine control computer module

We mentioned the saddle-shaped fuel tank on some rear-drive cars and SUVs, which are divided into main tanks and fuel tanks, but generally only an electric fuel pump is installed in the main tank. So how does the fuel in the tank compare to the main fuel tank? Engineers use the siphon principle, so that the fuel tank in the fuel tank through the suction pipe is sucked out and transported to the main fuel tank.

2017年4月4日星期二

How does auto alternator detect?




When the suspect is suspected of failure, you can initially detect the car, remove the alternator does not disassemble further detection. The tools used to detect can be multimeter, general DC voltmeter, DC ammeter and oscilloscope.

How to detect the alternator without a multimeter in the absence of a car alternator?

Turn the multimeter knob to the DC voltage 30V file, the red pen connected to the motor "armature" then column, black pen then shell, so that the engine running in the speed above, 12V electrical system voltage value should be about 14V, 24V electrical The system voltage standard value should be about 28V. If the measured voltage is the battery voltage, it indicates that the china alternator is not generating power.

Can also use car lights, flashlight homemade small test lights, etc., but also by changing the state of the car to detect.

Start the engine, turn on the headlamps, so that the engine speed from the idle speed gradually increased to medium speed, headlamps brightness increases with the increase in speed, indicating that the china alternator is working properly, otherwise no power generation.

When there is no computer control electronic device, you can use this method to detect. The engine control in the speed above, remove the battery to take the line (usually disconnect the battery on the line control the main switch), if the engine is working properly, indicating that the alternator power generation, otherwise the alternator is faulty.

The flashlight at both ends connected to the wire made of small test lights, connected to the alternator "armature" and between the shell. Use the wires to connect the positive and negative poles of the battery (or the same voltage) to the two magnetic fields of the alternator. The "F1" and "F2" ("AC" ), Let the battery to the china alternator excitation. Quickly turn the engine belt by hand, a small test light that the alternator is working properly, otherwise the alternator does not generate electricity.

There is no tool, then the alternator can not be removed to check, so only in the car inspection. Do not rely on any tools, then the hands can only be used on the car parts, we can use the alternator with a close engine to monitor.

When there is no computer control of electronic devices, you can use this method to detect:
First start the engine, and then open the headlamps, so that the engine speed from the idle speed gradually increased to medium speed, headlamps brightness increases with the increase in speed, indicating that the alternator is working properly, otherwise no power generation. This is a relatively simple method, there is a way, but need to remove the battery cable line, and then see if the engine is working.

What is the chassis strength?




The stability of the car chassis, refers to a good frame rigid, more adequate suspension support, when you drive these cars, it gives you a strong enough feeling of the chassis. However, this feeling is definitely not hanging hard sticks, if too tough, then it will be bumpy serious (No.: shock is not necessarily good control), the overall lack of rigidity and china air suspension is very hard, there will be a lot of system Of the noise, so that can not be called a solid chassis.

Chassis solidity can be divided into several, one of which is the degree of tranquility. In fact, the chassis noise to the car noise, hanging parts friction sound, after the rugged section of the metal resonance caused by the sound. As for the road noise, it is caused by the friction between the tire and the road, the general car factory will be in the round arch parts for sound treatment, if it is comfort-oriented models, then the noise will do better, in addition, will choose A more quiet tires.

The above mentioned first point - hanging parts and body friction is one of the factors, how to understand this? In fact, encountered in the uneven sections, the china air suspension of the joint bit is to make noise, and the easiest way to deal with is between the two contact points to join the rubber products, it can not only reduce the chassis due to vibration caused by noise, while allowing The whole chassis is more resilient to the pits. However, when a car is up and down to the chassis, when you pass through the uneven sections, you will only feel the china air suspension of the operation, when the pit will not have extra vibration, the chassis will absorb the excess vibration, While there is enough toughness to support, which will make you think there is no feeling of loose chassis.